
Four SATAIII (6Gb) PCIe V2 (10Gb) Support MAC, Windows, Linux Included Low Profile Bracket
S3Q-PCIe22 is a single-chip solution PCI-E Gen2 (V2 @ 5Gb/s) 2x lane (10Gbps) to 4x channels SATAIII host controller that takes SATA performance and features to enterprise levels.
The S3Q-PCIe22 base on Marvell 88SE9230 chip-set integrates Serial ATA III PHY technology capable of running SATA I, II and III. Support MAC, Window and Linux native AHCI protocol with PM supported Support hardware raid 0,1, and 10 in BIOS
S3Q-PCIe22 - Key Features
- 6Gbps SATA III Internal 4 Ports PCIe Gen2 x2 Lane Host Adapter
- Supports PCIe 1.0 and PCIe 2.0 motherboard
- Compliant with 10Gbps x2 PCI Express 2.0
- Fully compliant with Serial ATA specifications 3.0
- Supports SATA III transfer rate of 6.0Gbps, 3.0Gbps, 1.5Gbps
- Supports SATA I & SATA II & SATA III HDD, SSD, Optical Drive and Blu-Ray Drive o Supports ATA and ATAPI commands
- Supports Native Command Queuing (NCQ) o Supports totally max 7 drives connected
- Supports max one SATA FIS-based or Command-based Port Multiplier and max 4 drives connected to PM
- Low Profile PCIe Form Factor
- Regular size PCIe bracket on board and an additional Low Profile bracket included
- SATA Hot-plug capability
- Pin headers on board for HDD LED connection
- 64bit / 32bit Windows 8, Win7, Vista, 2008, 2012, Linux and Mac 10.x built-in AHCI inbox driver support, no additional driver required
- Supports Windows XP driver
- Supports Hardware RAID 0, RAID 1, HybridDrive mode by GUI or BIOS setting in Windows, but Non-RAID (JBoD) only for drives attached to PM o Fully RoHS compliant
Using up to two (2) PCI-Express Gen 2.0 (Gen 1.0 compatible) x2 lanes, this controller offers a 10Gbps bandwidth, a new bandwidth level of JBOD/RAID for SATA III
An embedded ARM-based CPU makes this product a pure hardware RAID controller and enables in-box driver support without additional driver installation. The included Marvell Storage Utility (MSU) provides a user-friendly interface to end users, while the Marvell RAID driver allows the drives to be used with a SATA port multiplier for increased system performance and capacity.
The Marvell HyperDuo offers a breakthrough embedded technology for new generation 6Gb/s SATA Controllers, enabled on the Marvell 88SE9230 and 88SE9220. Based on years of research and patent-pending software and hardware, HyperDuo enables 80 percent of the performance of an SSD at less than half the cost. Configured with one hard drive and multiple SSDs, HyperDuo uses intelligent algorithms to automatically migrate hot data to the SSD while enabling all data to be safely stored on a larger capacity SATA HDD for higher input/output operations per second (IOPS), throughput and capacity
With four (4) independent SATA 6Gb/s ports via 4x SATA 7pins ports, configured as RAID0 via our sBOX-S6 Here are the our screen shots:
Connect as Gen2 5Gb per lanes and HDD is connected as 6Gb/s per drives
Connect HDD as SATA III
Read and Write Speed as RAID0 over 500MB/s
For OEM or bulk quantity pricing, please contact sales@DATOptic.com.
Drivers | MAC OS 10.x - Driver-less Window7 and later - Driver-less Windows XP 32/64bit with SP2 installed Windows32/64bit |
SATARAID tools | Management Raid Utility (MRU) - Windows
Management Raid Utility (MRU) - MAC |
User Guide | S3Q-PCIe22-User Guide |
Part Number: | S3Q-PCIe22 |
Operation Mode: | AHCI Hardware RAID0/1/10 - Support Windows/Linux/MAC only |
Host Interface | Two (2) lanes PCI Express (PCIe) Gen 2 @ 10Gbps |
Device Interface | Four (4x) SATA port @ 6Gb/s per channel fully support PM ware (port multiplier) |
Speed | 4x Seagate SATA III Baracuda configure as raid0 Read/Wire over 500MB/sec |
Operating Environment | Temperature: 0o C to 50o C Humidity: 5% to 95% non-condensing |
Support OS | Windows XP/Vista/2003 Server/2008 Server /Win7*- 32bits Windows XP/Vista/2003 Server/2008 Server - 64bits Linux 32 / 64bit; Novel Netware Macintosh OS 10.4, 10.5, and 10.6* and later |